Temperature
AT-050
Temperature
Stainless steel immersion sleeve Nominal pressure: PN 40 bar, material: 1.4571.
Screw-in thread: G 1/2 A Outer Ø: 9 mm
Installation length: 50 mm
Screw-in thread: G 1/2 A Outer Ø: 9 mm
Installation length: 50 mm
ATM-050
Temperature
Brass immersion sleeve Nominal pressure: PN 16 bar.
Screw-in thread: G 1/2 A Outer Ø: 8 mm
Installation length: 50 mm
Screw-in thread: G 1/2 A Outer Ø: 8 mm
Installation length: 50 mm
D - Display OPP-SENS
Temperature
Display & control unit can be illuminated. With autoadapt and capacitive buttons.
Fits all round sensor connection heads with active
outputs. The unit is fitted with ribbon cable and
a reverse polarity-protected connector on the
electronics board and is ready for use without
configuration (autoadapt). The corresponding menu
for the transmitter is automatically displayed.
The unit is illuminated (only with 3-wire
connection) and has capacitive buttons. The
lighting duration, contrast and temperature
settings can be adjusted via the menu. With bus
transmitters, all parameters such as bus
addresses, baud rate, etc. can be configured
directly. The 5-point calibration is also
performed via this unit. IP 65 protection due to
the integrated seal. For configuration and
calibration: Multiple sensors can be configured
successively using one unit and then closed and
operated with the normal cover. Used as actual
value display: The display permanently replaces
the cover. Data sheet: 20902
Fits all round sensor connection heads with active
outputs. The unit is fitted with ribbon cable and
a reverse polarity-protected connector on the
electronics board and is ready for use without
configuration (autoadapt). The corresponding menu
for the transmitter is automatically displayed.
The unit is illuminated (only with 3-wire
connection) and has capacitive buttons. The
lighting duration, contrast and temperature
settings can be adjusted via the menu. With bus
transmitters, all parameters such as bus
addresses, baud rate, etc. can be configured
directly. The 5-point calibration is also
performed via this unit. IP 65 protection due to
the integrated seal. For configuration and
calibration: Multiple sensors can be configured
successively using one unit and then closed and
operated with the normal cover. Used as actual
value display: The display permanently replaces
the cover. Data sheet: 20902
D-NFC - Display OPP-SENS
Temperature
Display & control unit. With NFC interface and capacitive button.
Fits all round sensor connection heads with active
outputs. The unit is fitted with ribbon cable and
a reverse polarity-protected connector on the
electronics board and is ready for use without
configuration (autoadapt). The corresponding
measuring values for the respective transmitter
are automatically displayed. The unit has a
capacitive push button. The display has an NFC
interface. With bus transmitters, all parameters
such as bus addresses, baud rate, etc. can be
configured directly. The 5-point calibration is
also performed via this unit. IP 65 protection
due to the integrated seal. For configuration and
calibration: Multiple sensors can be configured
successively using one unit and then closed and
operated with the normal cover. Used as actual
value display: The display permanently replaces
the cover. Data sheet: 20902
Fits all round sensor connection heads with active
outputs. The unit is fitted with ribbon cable and
a reverse polarity-protected connector on the
electronics board and is ready for use without
configuration (autoadapt). The corresponding
measuring values for the respective transmitter
are automatically displayed. The unit has a
capacitive push button. The display has an NFC
interface. With bus transmitters, all parameters
such as bus addresses, baud rate, etc. can be
configured directly. The 5-point calibration is
also performed via this unit. IP 65 protection
due to the integrated seal. For configuration and
calibration: Multiple sensors can be configured
successively using one unit and then closed and
operated with the normal cover. Used as actual
value display: The display permanently replaces
the cover. Data sheet: 20902
F-10
Temperature
Air duct flange Bore diameter 10 mm, with screw
For OPP-SENS air flow and humidity sensors.
Movable along the length of the probe For
straight and round air ducts with lip for
airtight termination, 2 holes for screwing onto
the air duct. The flange is made of dark gray
plastic, including cross-head screw for fixing
the sensor.
Data sheet no. 20902
For OPP-SENS air flow and humidity sensors.
Movable along the length of the probe For
straight and round air ducts with lip for
airtight termination, 2 holes for screwing onto
the air duct. The flange is made of dark gray
plastic, including cross-head screw for fixing
the sensor.
Data sheet no. 20902
F-13
Temperature
Air duct flange Bore diameter 13 mm
For attaching the base temperature sensor on the
housing (standard). For straight and round air
ducts with lip for airtight termination, 2 holes
for screwing onto the air duct. The flange is
made of dark gray plastic, including cross-head
screw for fixing the sensor.
Data sheet no. 20902
For attaching the base temperature sensor on the
housing (standard). For straight and round air
ducts with lip for airtight termination, 2 holes
for screwing onto the air duct. The flange is
made of dark gray plastic, including cross-head
screw for fixing the sensor.
Data sheet no. 20902
F-6
Temperature
Air duct flange Bore diameter 6 mm, with screw
For OPP-SENS base temperature sensor. Movable
along the length of the probe For straight and
round air ducts with lip for airtight
termination, 2 holes for screwing onto the air
duct. The flange is made of dark gray plastic,
including cross-head screw for fixing the sensor.
Data sheet no. 20902
For OPP-SENS base temperature sensor. Movable
along the length of the probe For straight and
round air ducts with lip for airtight
termination, 2 holes for screwing onto the air
duct. The flange is made of dark gray plastic,
including cross-head screw for fixing the sensor.
Data sheet no. 20902
IO-BAC-S-AI1DI1-D-NFC
Temperature
I/O module BACnet. With display and NFC interface 1 DI. 1 AI 0 – 10 V/4 – 20 mA.
For connecting external portable devices with
relay and current/voltage output with spring
terminals. Inputs can be configured as NC or NO
contacts. 8 lid positions selectable. Analog
input: 0 – 10 V or 4 – 20 mA. Switchable with DIP
switch. Bus calibration (address, baud rate) via
the NFC interface on the display. Supply voltage:
15 – 30 V AC/DC. Power consumption: 160 mA (24 V
AC)/60 mA (24 V DC). Housing: Base: PBT, color
similar to RAL 7016. Display: PC, transparent.
Ring: PBT, color similar to RAL 1003. Protection
class: IP 65, (including seal ring). Strain
relief 2 x M16 and 2 x M12. Fast wiring with
spring terminals 0.2 – 1.5 mm². Permissible
ambient conditions: -20 °C to +70 °C. 0 – 95% rH
(non-condensing). Leakage resistance: => 100 MΩ,
20 °C, 500 V DC.
Data sheet no. 20915
For connecting external portable devices with
relay and current/voltage output with spring
terminals. Inputs can be configured as NC or NO
contacts. 8 lid positions selectable. Analog
input: 0 – 10 V or 4 – 20 mA. Switchable with DIP
switch. Bus calibration (address, baud rate) via
the NFC interface on the display. Supply voltage:
15 – 30 V AC/DC. Power consumption: 160 mA (24 V
AC)/60 mA (24 V DC). Housing: Base: PBT, color
similar to RAL 7016. Display: PC, transparent.
Ring: PBT, color similar to RAL 1003. Protection
class: IP 65, (including seal ring). Strain
relief 2 x M16 and 2 x M12. Fast wiring with
spring terminals 0.2 – 1.5 mm². Permissible
ambient conditions: -20 °C to +70 °C. 0 – 95% rH
(non-condensing). Leakage resistance: => 100 MΩ,
20 °C, 500 V DC.
Data sheet no. 20915
M-MOD-D-NFC
Temperature
Measuring transmitter for PT1000 transmitter Modbus with display and NFC interface, output Modbus.
1 input for PT1000 measuring sensor. For
connecting PT1000 cable sensors with 2 spring
terminals. 8 lid positions selectable. 10x offset
adjustable via rotary switch. 5-point calibration
and parameterization (address, baud rate) via the
NFC interface on the display. Output signal
linear due to microprocessor technology. Supply
voltage: 15 – 30 V AC/DC. Power consumption: 140
mA (24 V AC)/45 mA (24 V DC). Housing: Base: PBT,
color similar to RAL 7016. Display: PC,
transparent. Ring: PBT, color similar to RAL
1003. Protection class: IP 65, (including seal
ring). Strain relief for bus wiring. Fast wiring
with double-row spring terminals. Cable
cross-section 0.2 – 1.5 mm². Permissible ambient
conditions: -20 °C to +70 °C. 0 – 95% rH
(non-condensing). Leakage resistance: => 100 MΩ,
20 °C, 500 V DC.
Data sheet no. 20910 Delivery
time on request
1 input for PT1000 measuring sensor. For
connecting PT1000 cable sensors with 2 spring
terminals. 8 lid positions selectable. 10x offset
adjustable via rotary switch. 5-point calibration
and parameterization (address, baud rate) via the
NFC interface on the display. Output signal
linear due to microprocessor technology. Supply
voltage: 15 – 30 V AC/DC. Power consumption: 140
mA (24 V AC)/45 mA (24 V DC). Housing: Base: PBT,
color similar to RAL 7016. Display: PC,
transparent. Ring: PBT, color similar to RAL
1003. Protection class: IP 65, (including seal
ring). Strain relief for bus wiring. Fast wiring
with double-row spring terminals. Cable
cross-section 0.2 – 1.5 mm². Permissible ambient
conditions: -20 °C to +70 °C. 0 – 95% rH
(non-condensing). Leakage resistance: => 100 MΩ,
20 °C, 500 V DC.
Data sheet no. 20910 Delivery
time on request